BIOSTAR PT890 775 Serial ATA RAID Driver
MegaRAID SATA X RAID Controller MegaRAID SATA Plus] PCI Bridge a PT PCI to PCI Bridge Controller a K8T PCI to Ltd Yamakatsu Electronics Industry Co Ltd Biostar Microtech Int'l .. 86C Trio64V2/DX, 86C Trio64V2/GX Plato/PX , , Socket VIA PT+ BIOSTAR PT SE; HDDg Serial ATA II Western Digital 16MB Special RAID. Medion MS MS MS Motherboard socket for MD MD VIA PT Slots Serial ATA RAID 0, RAID 1, RAID 0+1 und JBOD.
|Supported systems:||Windows 2K, Windows XP, Windows Vista, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10|
|Price:||Free* [*Free Regsitration Required]|
BIOSTAR PT890 775 Serial ATA RAID Driver
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied BIOSTAR PT890 775 Serial ATA RAID of merchantability or fitness for any purpose.
Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor s approval in writing.
The content of this user s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user s manual. All the brand and product names are trademarks of their respective companies.
Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation. Before you take the motherboard BIOSTAR PT890 775 Serial ATA RAID from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.
Full text of "Computer Power User Volume 4 Issue 11"
Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not BIOSTAR PT890 775 Serial ATA RAID to bend or flex the board. Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. Keep the computer from dangerous area, such as heat source, humid air and water. Remove Pin Cap before installation, and make good preservation for future use.
Pin Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a degree angle.
- FCC Information and Copyright - PDF
- Drivers for Biostar PT SE verx motherboard (Socket ) on FTP
- View File of Package pciids - openSUSE Build Service
- Quest Cross Reference
- Ask a Question
- Biostar P4M890-M7 SE - motherboard - micro ATX - LGA775 Socket - P4M890
Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation.
Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. This completes the installation. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin 1.
When connecting with wires onto connectors, please note that the red wire is the positive and should BIOSTAR PT890 775 Serial ATA RAID connected to pin 2, and the black wire is Ground and should be connected to GND. Unlock a DIMM slot by pressing the retaining clips outward. The IDE connectors can connect a master and a slave drive, so you can connect up to four hard disk drives.
This PCI slot is designated as 32 bits. When the jumper cap is placed on pins, the jumper is close, if not, that means the jumper is open. Pin opened Pin closed Pin closed 3.
It allows user to connect the PC case s front panel switch functions. Headers for USB 2.
Biostar PT Owner's Manual
It will disable the output on back panel audio connectors. Remove AC power line. Set the jumper to Pin close.
Wait for five seconds.