Gigabyte GA-H55M-S2 Intel SATA Driver
Placa Madre Gigabyte GA-H55M-S2 S Placa Madre Gigabyte GA-H55M-S2 Processor Support for Intel ® Core™ i7 processors/Intel ® Core™ i5 IDE ATA Chipset: 6 x SATA 3Gb/s connectors supporting up to 6 SATA 3Gb/s devices. GA-H55M-S2 LGA socket motherboard for Intel Core i7 processors/intel Core and features in this manual may be made by GIGABYTE without prior notice. Realtek RTLE x1 Intel H55 Dual BIOS D-Sub 6 SATA 3Gb/s PCI Bus The Gigabyte GA-H55M-S2H Motherboard feature the Intel H55 Express chipset supporting Socket The.
|Supported systems:||Windows 2K, Windows XP, Windows Vista, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10|
|Price:||Free* [*Free Regsitration Required]|
Gigabyte GA-H55M-S2 Intel SATA Driver
You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module con- nector match the pin assignments of the motherboard header. Gigabyte GA-H55M-S2 Intel SATA purchasing the op- tional COM port cable, please contact the local dealer. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may Gigabyte GA-H55M-S2 Intel SATA lost.
You may clear the CMOS values by removing the battery: From what I could tell, the board's serial number is on a white sticker along the outside edge of the pin ATX power connector, while the board revision is silk screened in the upper left corner of the board.
The board used in testing was a version 1. The area surrounding the CPU socket is fully free of obstructions, with low profile power circuitry put to use for those capacitors closer to the socket itself. The CMOS battery is located directly to the left of the socket, with the front panel audio header Gigabyte GA-H55M-S2 Intel SATA its upper left just under the rear panel header.
The four integrated DDR3 memory slots are below the CPU socket area, in a 2x2 bi-colored configuration with the white colored slots reserved for the primary memory modules. Dual Channel memory mode activates with matching modules Gigabyte GA-H55M-S2 Intel SATA in like colored slots.
The board's Intel H55 chipset is located directly below the two PCI slots, covered by a passive low profile heat sink. While there is no active air flow over the chipset under normal operation, we found that the chipset heat sink barely got warm even under overclocked scenarios. Note that to clear the CMOS, you Gigabyte GA-H55M-S2 Intel SATA jumper the poles of the header, with its normal operating mode being left un-jumpered.
After the memory is Gigabyte GA-H55M-S2 Intel SATA, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double Gigabyte GA-H55M-S2 Intel SATA original memory bandwidth. The two DDR3 memory sockets are divided into two channels Gigabyte GA-H55M-S2 Intel SATA each channel has one memory socket as following: Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance Hardware Installation 16 Installing a Memory Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module.
Follow the steps below to correctly install your memory modules in the memory sockets. Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket.
As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the Gigabyte GA-H55M-S2 Intel SATA and insert it vertically into the memory socket. The clips at both ends of the socket will snap into place when the Gigabyte GA-H55M-S2 Intel SATA module is securely inserted. Hardware Installation 17 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: Make sure the motherboard supports the expansion card.
Carefully read the manual that came with your expansion card. Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage. Locate an expansion slot that supports your Gigabyte GA-H55M-S2 Intel SATA. Remove the metal slot cover from the chassis back panel.
Download Gigabyte GA-H55M-S2 (rev. ) Realtek LAN Driver for XP
Align the card with the slot, and press down on the card until it is fully Gigabyte GA-H55M-S2 Intel SATA in the slot. Make sure the metal contacts on the card are completely inserted into the slot. Secure the card s metal bracket to the chassis back panel with a screw.
After installing all expansion cards, replace the chassis cover s. Turn on your computer. Install the driver provided Gigabyte GA-H55M-S2 Intel SATA the expansion card in your operating system. Installing a Graphics Card: Gently push down on the top edge of the card until it is fully inserted into the PCI Express slot.
Make sure the card is securely seated in the slot and does not rock.